By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for brfc7

Here is a list of all the postings brfc7 has made in our forums. Click on a thread name to jump to the thread.

Thread: Mini Blitz
14/02/2018 20:22:34

To show the size difference, here's my finished Micro and part built Mini. The rear of wing is lined up with one another.

11

Baz

09/02/2018 13:57:41

Since I completed my Micro Blitz a few days ago and haven’t managed to maiden it yet I thought I’d get straight on with building the Mini Blitz too yes The build will be the same as the Micro using an extra rib to sandwich the fins in between. Next time I build either of these models I’m just going to make solid sheet wings as will save a lot of hassle and with brushless motors the extra weight will be cancelled out with loads of POWER wink

c6571a66-48bd-426c-9c4c-b61ea8ffbe44.jpeg

Baz

06/02/2018 22:14:13

Finished my Micro Blitz tonight yes she's ready for maiden

8

Running on 2s @ 40w so that works out about 100w per lb so should go ok.

Here's my install with 2s 450mah lipo

9

Baz

01/02/2018 22:14:35

All covered now yes

I need to install the horns on to the elevons and tape them on and then I can connect the servo pushrods followed by gluing the servo cover on and I also still haven’t glued fins in.

 

7

Baz

Edited By brfc7 on 01/02/2018 22:35:07

24/01/2018 10:58:55

As mentioned in previous post when I make the mini I’m going to use the stock motor from a radjet that I never used. Probablys with a 5x5 prop or their abouts on 3s 1300.

Ken can you remember the power figures from your radjet? I know you had standard motor on 3s but what prop and watts/amps did it produce?

Baz

24/01/2018 10:38:41

What’s your setup Ken?

Baz

23/01/2018 23:47:32

My progress so far -

6

The fins are still removable and I will decide weather to leave them like that or permanently glue them in after I cover it. Hatch has a tongue at front and earth magnets at the rear, Servo arms will come out of the holes in fuz side and be made to measure wire with Z bends at both ends.

baz

23/01/2018 10:31:27

I got all my wood for both the micro and mini from Phill’s models Ken. I even cheated for the elevens as I bought pre shaped aileron strip and just cut it down to the correct size. The motor and esc for the micro I already had and for the mini I’m going to use the motor that came with my radjet that I never used.

Baz

23/01/2018 10:10:07

Nice to see you back at the building board Kenny. I notice you’ve went down the same route as me, putting in an extra rib to slot fins in between yes

I’m getting well on with my micro blitz but haven’t took any recent pics. The servos are in and I’ve just finished the top hatch. It’s secured with a tongue at the front and is held at the back by earth magnets. Next is to start covering it and then tape on elevens and connect to servos before I can glue the rear deck on.

I also bought enough wood to make the mini so will start that soon too.

Baz

07/01/2018 03:36:25

Paulo if you look closely at all my pics you might see that the fuz at the front are different lengths. I made fuz sides as plan but then when installing motor I had the same problem that the prop would hit fuz sides. I thought about putting in another motor former but instead I just chopped off about 10mm from the side cheeks at either side of fuz.

Baz

06/01/2018 19:45:57

Glued fuz sides on to wing then the motor former and motor.

Motor is an 1811 2900kv, 6amp esc that I took out of a converted Multiplex Fox. I ran that on 2s swinging a 6x4 producing around 40w. Might put a smaller prop on.

4

Then sheeted the underside

5

Next is to make the top hatch, It will be a single piece of balsa with a tongue of ply at front that will slot under and held down at the rear with earth magnets on a piece of ply. Also need to sort some servos.

baz

Edited By brfc7 on 06/01/2018 19:49:11

Thread: Ebay sellers...
18/12/2017 23:31:04

Cracking deal this one

**LINK**

"As pictured very original good condition, this has futaba gear, it's not been flown for a while, if you know about it you can see its not damaged or anything"

Thread: Mini Blitz
18/12/2017 09:00:47

 

The way I’ve made mine Rene with the extra rib, I could just slot the fins in as they are a tight push fit and I haven’t glued them in yet. I’m installing the fins without the stated angle, mine are straight vertical.

Baz

Edited By brfc7 on 18/12/2017 09:03:12

16/12/2017 21:56:36

Forgot the wife was at work tonight, so back out came the balsa yes

I cut out 2 fins and the way I've decided to do it is to put another rib in just far enough away from another one so I can slide fins in straight vertical. I'll probably cover the wing first then glue the fins in.

2

I also cut out 2 fuz sides and dry fitted them.

3

Baz

16/12/2017 18:06:00

Made a start today on the micro

08f42a26-215b-4485-917a-6e9b2337afd7.jpeg

 

Edited By brfc7 on 16/12/2017 18:06:24

Edited By brfc7 on 16/12/2017 18:08:50

14/12/2017 23:29:26

Just got the magazine today and I'm going to build both the Mini and Micro and probably get the Micro in the air first.

Baz

Thread: Nexus tail part needed
16/08/2017 11:02:14

Posted by David P Williams on 16/08/2017 10:15:58:

There's a whole tail set here. I've bought quite a few bits from him to keep my old Hirobo Lama going.

Found that this morning David, price puts me off a little especially as the next crash with it will most probably be its last as it's not worth spending any decent money on. I had to buy a main gear for it last year and that was £20 and it looks like you'd be lucky to get one for £30 now.

I'm waiting for the shop in Australia getting back to me as tried to order online again but same error message comes up. So I've messaged them direct.

Thanks for suggestions so far.

Baz

16/08/2017 09:15:48
Posted by Phil 9 on 16/08/2017 08:54:41:

but the one from Australia could be the last one **LINK**

I tried to order the one from Australia last night but it just kept saying error after payment screen.

Baz

15/08/2017 22:50:41

Can anyone help keep my old girl in the air. I'm after a tail slide (original part H3045 Tail slide ring set) the picture below shows the part I'm looking for, on mine the silver pin is wobbling indecision I've looked online and can't get a new one (possibly one in Australia)

But I thought I would see if anyone has a crashed nexus where this might have survived.

H3045 tail slide ring set

H3045 tail slide ring set

Thanks Barry.

Thread: Tony Nijhuis' new Vulcan
26/05/2017 22:51:13

Looks great Craig, I'm looking forward to seeing it myself.

baz

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E! 

Email News - Join our newsletter

Love Model Aircraft? Sign up to our emails for the latest news and special offers!

Latest Forum Posts
Support Our Partners
Overlander
Slec
Gliders Distribution
Expo Tools 14 July
Airtek Hobbies
Wings & Wheels 2018
electricwingman 2017
CML
Advertise With Us
Sarik
Latest "For Sale" Ads
How has your building graduated?
Q: Did you start with ARTF and move to building from kits or vice versa?

 Started with ARTF moved to building from kits only
 Started with ARTF moved to building from plans only
 Started with ARTF moved to building from kits and building from plans
 Started with building kits or from plans and moved to ARTF
 I only build from kits or plans
 I only build ARTF
 I only build from kits
 I only build from plans
 Other (Please specify in thread)

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us