Jump to content

David Germany

Members
  • Posts

    125
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

David Germany's Achievements

0

Reputation

  1. Thanks Guys, I'll stick with my original choice then (the 30FS) and keep it light and slow. I was hoping for a similar flying speed as my Junior 60 which also has an ASP 30FS. Also, on checking the fit of the Saito 45 I would have to lengthen the cowl even more than the plan which would detract even further from the scale outline. Thanks again, just needed some reassurance after being distracted by some of the t'internet content.
  2. Hi, I'm building a Ben Buckle Fokker D8 from an old kit, it will be built with no dihedral but with ailerons with wing mounted mini servos. Originally I had intended to fit an ASP 40FS but I do have the option of a Saito 45 Special. If I need a shed load of lead to balance with the ASP then I guess I may as well use the Saito, Would the extra weight / power of the Saito require more strengthening to the front end ? I hope to keep the overall weight as low as possible to keep the flying speed low. Any advice on the engine options would be appreciated.
  3. Hi Geoff, I have just finished my Dremel CNC from the Nikodem Bartnik design, I'm using Fusion 360 for CAD/CAM and Cncjs as the interface. Currently just messing around using a Dremel 3mm routing bit. Have you tried vinyl cutting yet, I've purchased a Chinese drag knife but need to make an adaptor to suit, I'm also interested in fitting a laser module and wondered what the capacity of these small units was in the real world, mainly in balsa and lite-ply / laser-ply. Any info from anyone would be appreciated.
  4. Yes Martin, definitely selected 5 cell (6V) on the tester. A good point though, would be an easy mistake to make.
  5. Fully charged the battery then discharged at 2A as C8 suggests, after 80 minutes battery was down to 5.7V so looks OK. Will try the extended stick stirring with meter attached tomorrow. I'm more & more inclined to think this was a connector / wiring intermittent fault so will replace the switch / harness and connectors and bind connectors with floss to secure. I think we are also going to replace the Rx anyway.
  6. Receiver was replaced after second crash, so unlikely to be the culprit. I'm thinking it's got to be along the battery / lead / connector / lead / switch / lead / Rx connection route. We checked the battery (2500 mAh 5 cell NIMH) after the crash with a load tester and it showed OK, and it still shows OK after 5 days so I don't think it's that but I will check for voltage drop with all servo's operating. I can't make the switch fail either even with lots of waggling. As a matter of interest does anyone else get servo movements when switching on the Rx ? with the Tx on obviously.
  7. It's the re-connection and subsequent servo twitching that ultimately caused the crash. On replicating the fault on the ground the ailerons would travel about 60% and the rudder about 20% in the opposite direction. You're right though about no servo movements when the power is cut, switching off the receiver and leaving it off the servo's do not move. I was flying the model on the last occasion and it did feel as though something was wrong in the couple of seconds before the model flipped, my recollection was that the throttle was not responding, then the model rolled over and went into a dive, I then found I had control again, righted the model and cut the throttle hoping to glide back down.(it was only at about 15 / 20 feet at this point. Then the same thing happened but this time it just rolled into the ground.
  8. Whilst investigating a series of crashes with a club members Wots-Wot (kit built) it seems the most likely cause was a momentary power interruption causing the servos to twitch on re-connection. Receiver and servo's have been replaced to no effect. The cause of the interruption is most likely a faulty switch / harness or connection, and to this end we are replacing all wiring and connectors. However this has got me to thinking why do some servos move temporarily on power-up, whilst some don't, and can anything be done to prevent this. It does not seem be brand specific, affecting Spektrum, Futaba, Hi-Tec and New-Power that I know of. Obviously this is not normally an issue as we do not expect to switch the model off in flight but it would be interesting to know the explanation of why it happens.
  9. Hi Birgir, I realise it's some time now since your Bleriot was on topic but I'm after a bit of info subsequent to crashing mine at the weekend. My error, let the airspeed drop too far on the landing approach in zero wind, dropped onto the runway from about 5 feet. It's not as bad as it looks, the rear 'birdcage' has shattered and the front undercarriage support structure has broken away. All flying surfaces are undamaged. As I no longer fly at an electric only site I'm thinking of rebuilding as IC powered. What was your final ballast weight with the SC30FS ? I have a Saito 45 Special which is 470g, and an RCV58CD which is 540g. My preference would be the RCV as it is compact and sounds a bit more scale than the Saito. It also runs great inverted. If these weights are less than your total up-front weight I should be OK. Hope your Bleriot is still surviving, David
  10. Thanks for the links, I've finished the translation (2076 words), Using the instructions and the pictures on the build blogs it starts to make sense. Plus I've learnt some Italian. Noticed that the wings are built in a jig and include alternative ribs for fixed u/c or retracts, I have a set of 60 size electric retracts which I hope to fit.
  11. Masher, no I couldn't find any online blogs, can you remember where they were ?. I had noticed the laminated leading and trailing edges and put this down to their laser cutter not being able to cut the full thickness.
  12. Thanks for the replies, I've found an on-line translator site that seems to work OK. As many of the words repeat it gets easier as you go, I'm about 2/3 of the way through (1014 words). I will try the email route as well though. The first line of the instructions begins "Procurarsi un piano" apparently this does not mean "Get a piano", rather "get a building board" !!! There are no full size plans for the fuselage, instead it is built in a jig using parts included in the kit. Thanks again for the replies.
  13. It's actually printed on the plan, but I estimate about 1500 words.
  14. Have just purchased one of the above kits, it's a big box nicely packed and looks to be of good quality. Problem is the instructions on the plan are all in Italian. I guess I could just build from the plan but I'm concerned that the quite lengthy instructions may contain some valuable tips which if ignored could prove embarrassing later on in the build. Last resort will be to use an online translation site, but that could take some time. Any help would be appreciated.
×
×
  • Create New...