Robert Armstrong 2

Posted by Robert Armstrong 2 on 26/04/2019 20:19:24: Help I have a 14SG on version 6.0 software. The Ripmax site shows version 8.0 now out. Can I update direct to v8.0 or do I have to go through v 7.0 first? Would like to avoid two steps if possible. Thanks in advance if anyone knows. Thanks Malcolm. Don't use non-Futaba receivers. Used to on a previous (T8) system but had a couple of odd crashes where the model seemed to stop responding, though post crash tests seemed to show the radio system working normally. Decided the relatively small cost saving was not worth the cost of peace of mind. Even more true now FHSS rxs are available.

Help I have a 14SG on version 6.0 software. The Ripmax site shows version 8.0 now out. Can I update direct to v8.0 or do I have to go through v 7.0 first? Would like to avoid two steps if possible. Thanks in advance if anyone knows.

I have had no problems with DPD and only one problem with RM. I sent a small package using Recorded Delivery to Horizon Hobby for repair (before they moved). I got it back from HH fixed and the RM Trace still said that it had not been delivered. I suppose I should have asked for a refund as I clearly didn't get the service I paid for.

Wheelspin models have the bare airframe for that model. Listed as 'shadow stock'. Most of their aircraft spares seem to be, but I have had good service from them and am very impressed with their spare parts section of the website. Very well organised. The physical shop is a washout for aircraft parts, specialise in cars. Clue is in the name I suppose

Rather tatty Chipmonk and foamie vampire.

Never heard anything from Mark. I sent him a PM cancelling my request for one. I looked it up just now. It's listed as 'unread' in my sent messages box.

The print of the ailerons etc in yellow Rigid Ink PLA didn't come out successfully. Looks under extruded. Oh dear, going to have to calibrate the settings for each roll of filament individually. On the plus side, the yellow pla glues together well with ZAP medium CA and kicker.

Test piece came out bang on the target weight using their recommended S3D settings. Seemed reasonably robust and printed without any problems despite their warning that they dont recommend printing parts separately. I can't fit their S3D factory files onto the print bed of my machine so I am loading individual stls. The first attempt at printing two wing parts together failed with a weak layer in one of the parts only. Thought that I might have bumped the printer so started the print again, Same result, so must be an artefact in the sliced file. That used up the tag end of a roll of PLA so waiting for some more. Will try printing the ailerons rudder etc in yellow, but dont fancy that for the whole airframe.

Downloaded the test piece for the 109 from Thingiverse. I use Simplify3d so the Youtube video guide has the settings, though for an earlier version of S3D, which now has some extra settings available. Interesting to see how long it takes. One almost gotcha; Their version of S3D has speeds in mm/sec. Mine defaults to mm/min.

Was thinking of trying the 109, probably without u/c, to see how well it works on my printer. I was interested by the recent review of the Stearman, but disappointed that it was supplied as a kit of parts from Aerofred.

The model shown on the 3dLabPrint web site seem quite interesting, but the information quoted includes a bed size larger than the bed size of my printer. I have emailed 3DLabPrint to ask whether the quoted size is the requirement for the largest individual part or whether its for a collection of parts. So far they have not replied (about a week). I have a Flashforge with a bed size 230X150X150. They seem to have developed everything for the Prusa I3, which has a bed size closer to square. Height is OK on mine. Anyone know anything about the part sizes for any of the planes?

My wife and I went for the first time early September. I really enjoyed it. The pool area is nicely landscaped and supplied with chairs etc (and a bar close by) so if your partner likes sitting round a pool its great for them too. While we were there everyone else we spoke to had been there before (mostly more than once). Spiros said that about 80% of his business is repeat customers. Food was very good too.

I used the 'report an issue' feature in the Pocketmags app, which sent an email to them. To my surprise, I got an email back within a couple of hours to say that they had 'added the issue to my account'. Pleased that they fixed it so quickly, slightly worried by the terminology that the issue may recur with the next issue. Wonder if there is a wider problem? Change of year on the issue not matching subscription details in some way?

I tried the option 'Iam an an existing subscriber etc.." and successfully logged in. It let me download a back issue, but still wants me to pay for the current issue. On iPad. I can access the current digital issue from my laptop OK.

Problem with Pocketmags. Not the first either. The new issue showed up but it wants me to buy it. Tried logging in again. Success reported. Still wants money. My subscription doesn't run out till Feb 2018. Though I am never sure whether that means the February Issue (which comes out in January) or the issue which comes out in February (the March issue). I probably ask every year when I renew, but the n forget.