Jump to content

Flying Flea

Members
  • Posts

    31
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Flying Flea's Achievements

0

Reputation

  1. Hello Stephen, I called into the indoor meeting at the Velodrome on Saturday and hoped to see you there, but maybe missed you. It's on again next month on the 7th December, hopefully it may be a regular gathering, quite a few from the Bury club looked to be there. I didn't see it on the North West events page of the BMFA website, it was in Aeromodeller though. Regards, Kieran.
  2. Love the photo, I think it's looking south from Tebay. A local lass told me that just on the right hand side just out of shot is a heart shaped wooded area, where a pilot of one of the fast jets went in, his wife had the trees planted as a memorial to him. You often get the Typhoons coming through the valley very low, it's quite a sight. If you do get stuck in the traffic there it is a nightmare, the locals will quite happily drive for miles to avoid getting stuck on that bit. The worst M6 stretch seems to be Warrington to Birmingham either way, always accidents or roadworks. p.s. my mistake that should read on the left hand side as you look at the photo. Edited By Flying Flea on 24/05/2019 10:33:21
  3. Thanks for posting this film, some of the best aerial footage I have ever seen. Very sad ending to the story though. Regards, Kieran.
  4. Hello Ian, It's been great seeing how you've renovated your workshop, the work on the doors is really good. Some nice ideas on there for storage aswell, like the Drain Pipes, I wish I could plaster like you, whenever I've tried, I end up with more on the floor than the wall. Would a sealing coat of thinned PVA help to stop the flaking on the walls, before you paint them? Keep up the good work. Regards, Kieran. p.s. How's the Flea? looked great in the photo's in the mag.
  5. Hello Gary, We use the little axminster bandsaw at work and it's pretty good. You will probably find that most machines look similar, because they are mainly made in China and then re-badged. The Schepach on the other hand is of German origin, I think and again is a nice little machine. The axminster is used nearly every day and has proved to be reliable and accurate, just take your time setting it up at first and away you go.Regarding the blades, we generally use a 6mm (1/4" wide blade with 6-10 Teeth per inch, this gives a good finish and is a good general purpose blade for cutting curves and straight edges. If it's mainly just straight cuts you're after, you could go for a 12mm (1/2" wide blade. The wide blade is better for straight work and the narrower blades are better for cutting curves. Hope this helps a bit, good luck, Kieran. p.s. Make sure to keep your fingers well away from the blade when cutting and use a push stick if you do go near it.
  6. Hello Ian, Nice write up, the Flea looks superb. Perhaps the problems were down to the pilot,he looks a bit like Prince Charles! Regards, Kieran.
  7. Hello Ian, Congratulations, very well done! I'm sure you and Ceejay must be well chuffed, thanks for the video,great stuff. Regards, Kieran.
  8. Hello Ian, They look great together, nice to see Henri in the office, will you be putting Bertie in? Which Greenacres do are you taking your flea to? is it the end of May or the June fly in, as I'd love to come along and see it flying, sorry for all the questions but I've really enjoyed following this thread. Good luck with the maiden! Regards, Kieran,
  9. Hello Mark, Brilliant video, keep up the good work. Any chance that you will release a plan or kit? I'd love one of those! Regards, Kieran,
  10. Ian, Wish I had a fraction of you're drive,it looks like it's nearly there now, good luck with the first flight! Regards, Kieran.
  11. It has to be a school boy error! (sorry I could'nt resist) I've also got workshop envy after seeing those doors, very nice. A lot of the full size Fleas ended up with warped rudders, the one at the museum in Manchester had a definate bend in it. Is there any trick to knowing how much tension is needed on the Diatex Ian? Regards, Kieran.
  12. Hello ceejay, Any chance of you posting a copy of the Henri Mignet photo, I'd love to see that. I've always liked flying wing designs and I am really looking forward to following your project. Is the info on the Archaeopteryx freely available? Thanks, Kieran. Edited By Flying Flea on 17/03/2014 12:38:03
  13. Hello Ian, I've really enjoyed watching the rapid progress with you're Flea, in particular the Diatex covering, it's been an education. You seem to have all the flea info I can think of, have you been in touch with Ken Ellis from Flypast magazine yet? I'm sure that he would love to see what you're doing. Ken is the Flying Flea Archive,he will have all the info you could ever need and he's a real gent to boot. He wrote the book "Henri Mignet and his Flying Fleas" with Geoff Jones, it's a great read, anyway good luck with the rest of thr build, I'm looking forward to it. Regards, Kieran.
  14. Hello Stephen, You're Flea is looking good, Ihope to get to the next Rochdale indoor meet and see it fly. I've attached a couple of photo's of the Scott engine on the HM14 in the museum of science and industry. The photo's are from Airliners.net,there are some really good pictures on there. Regards, Kieran.
×
×
  • Create New...