Bruce Austin

Ah, now I see what you've done, Leccyflier. I like that ply "insurance". I did a dry mockup direct to the servo arm, just like you, and i was a wee bit concerned about keeping the servo tight in place. I must admit that I prefer separate servos for my ailerons. That gives a lot more flexibility for flight modes. But then, I suppose, that when this plane was born, there was a limit to the number of radio channels, and still be able keep the hobby affordable. I have a Taranis Plus which gives me all the channels I need, and the receivers can be very compact indeed. Go With the Flow Bruce

Thankyou very much Trevor for that photo and the description. I can "see" the geometry now. Thankyou also Grumpynome. Go With the Flow Bruce

Hi there Leccyflyer, yes please, a picture would be a big help. What size servo did you need to use on that bowden setup? While we're at it what size servos did you use on the rudder and the elevator? I presume you are using metal gear servos? Go With the Flow Bruce

Hi there Guys, and Trevor Wood in particular. (Posting on page131 of this forum). Hey there Trevor, I have a Ridge Racer without any electronics. It has the same one piece bowden cable for the ailerons. There is a little "L" shaped wire soldered to the cable. I am puzzling what kind of linkage is needed between that and a servo. I really would appreciate a description, sketch, or photo of that linkage arrangement. My plane is virtually pristine with no damage to the glass fuse or to the glass veneer on the wings. The original blue translucent canopy is un scratched too. All the cables and linkages are still there for the elevator and the rudder. I quite fancy getting this into the air. Go With the Flow Bruce

Hi there "Nostalgia Guys" I'm in my 70s but only started RC flying about six years ago. ( A late starter) Anyway, two or three years ago I was given a slope soarer (with a towing hook fitted. I don't know what the name of the model is, but it seems to be all original. It has an all glass fuse measuring 43.5 inches from tip of the nose to trailing edge of the elevator. It has fully glassed polystyrene core wings, of 74.25 inches span. It has ailerons which are "solidly" linked and driven by one servo which drives an "L" shaped hook soldered to the stranded Bowden cable, which is still wworking. How is the servo arm configured to operate this bowden hook arrangement, I wonder??? How tricky might it be to fit separate servos into the wings??? How to get the servo leads there??? Go With the Flow Bruce

Thanks Steve for your response, and suggested browsing. I did do some other scratching around as well, and now have a clearer idea of the options. Currently considering the 2.5 meter Geronimo £460. plus bits and pieces. Need to discuss budget with "senior management" It seems a nice size, and light weight for the slope side and thermal hunting, which is my primary objective. Lots to explore and read the reviews. Go With the Flow Bruce

Hi Glider Guys, First of all appologies, if I'm in the wrong thread. If so I'm happy to be redirected. I enjoy casual slope and thermal gliding with my volantex P2000 V2 and ASW28 V2 foamies. I love the noiseless flying with the local Red Kites. In summer I can get over an hour with four minutes of motor, and have a Taranis Plus for programming various "subtlties wing settings"!!! I've only been flying for four years, and am retired in my seventies. I fly mainly on the slopes of the Chilterns, but I have flown successfully off the Cornish cliffs, also. I'm currently "wondering" about possible options for more thermally performing gliders between 2 to 3meters, to better catch the higher thermals, and for the related eyesite reasons. My flying area has a few prickly bramble runners hiding in the grass, so, that puts me off thinking about covered skeleton type wings. (I don't mean any disrespect to anyone, I'm just looking at practicalities for me). I'm definitely not looking to break the bank, but for example the Geronima is a nice looking and lighter weight glider and might well be the next sort of step to take. HOWEVER I would like to hear some suggestions about possible models and comments on how thorn proof their various stock types of wings might be. On my foamies, I do apply 3M clear tape to the leading edges which seems to work very well, this does of course add extra weight, but preserves the wings. My foamies have the typical Volantex plastic fuselages, but I land on grass, so fibreglass fuses would probably be OK???? My budget would prefer to be under £400.oo fully equipped with electric motor and all servos. Yes, probably a few chuckles out there, but I'm having a try, and maybe there's a few others out there with a similar quest???? I'm not into finding highly technical build solutions, having limited experience, other than buying foamie kits and then fitting servos and motors. (very basic stuff) I look forward to your various comments, observations, and experiences, with whichever suggested models you might come forward with. Tell me the budget is crazy, and make further suggestions, if you think that can help me and other like minded aspiring thermally folks. Go With the Flow Bruce

Hi electric thermalling guys. I enjoy casual gliding and thermalling with my foamies (P2000 V2 and ASW 28 V2) I mainly launch off a slope or sometimes off a cliff, and use the motor more as a "rescue" or to gain some height, for more thermalling. My flying location has quite a few thorny brambles in the landing area I am "just wondering" at this stage about the possibility of aspiring/ upgrading to a less heavy and more slipstreamed higher performace model type. Yes, I hear your comments, "haven't we all"!!! I don't want to break the bank, BUT what are the current options??? I am looking at minimum 2.000m and less than 3.000m because the eyes are not quite what they used to be. I'm not looking to be hot linering, but rather to be taking it easy hunting the thermals. Covered balsa frames are lighter for sure, but the film won't last long in the thorns, so what next? Carbon fibre is probably a cost step too far. Glassed wings? Obichie covered foam? I don't want to Build, but rather buy off the shelf almost ready to fly, if possible. What advice can you offer please. I'm in S East England on the Chilterns. Go With the Flow Bruce

Hi Tony, I realise this response is for last years query, but maybe you are still monitoring??? I fly the P2000 first version as well as the V2. My experience is that by moving the CoG rearwards, you might well have more chance of getting the lift. I fly off a slope mainly, but there are some days with just a whisper of a breeze, and then the thermals are more stable. I can ease the CoG rearwards and the Phoenix can thermal reasonably well, during the summer. Go with the Flow Bruce

Thanks Denis for your input. Long story short, I've got my money back. So, Denis, I was, and still am, looking for something that has stabilising options with "return to home". Preferably already able to just plug in. Soldering is not out of the question, but prefer not to, if possible. Have you any recommendations, please? Go With the Flow Bruce

I have tried to order a Bigaole from Reds Radio Contol. They claim to have stock. My order went in at the end of May. Half way through June I followed up and was told they are expecting a delivery any day. Still nothing on the 26th June. has anyone else had a similar experience with Reds RC? Go With the Flow Bruce

Hi there Dick, just an update for you. I haven't gone the warmliner route yet. I was tempted, and succumbed to a Lanyu HK ASW 28 glider (2.6 meters). definitely not a warm liner of course, but flies nicely on the slope. I also created a hybrid e glider using a FMS Fox 850 fuselage combined with a Staufenbiel DLG 1000 wing. This flies quite nicely from the slope also. It has a large wing in relation to the fuse and is great in a breeze. I haven't lost sight of the warmliner urge, it's just on hold for now. Go With the Flow Bruce

Oh, I forgot to comment on your suggested Saphire. That does indeed look very nice. Go With the Flow Bruce

High Dick, thank you for responding. Yes I suspected an all in one model would not be possible. My priorities are probably as follows. Budget aproximately £300-400 fully equipped, if that seems feasible. 1 Thermal with motor to get to altitude. Not interested in spot landing competitions. I prefer casual for fun , relaxed flying. 2 Slope with motor to save a long walk Speed is not really a requirement. That's a good point about speed and hatch being a weak point, thank you for pointing that out. Go With the Flow Bruce

Very interesting, I just found this thread today, and I am just reaching exactly the same situation as Glenn was when he started this thread. Only, I'm not looking to break the sound barrier. First question is how far have you progressed, Glenn since your last post? I am looking for suggestions for possibly a warmliner, but leaning more toward slope and thermalling. Probably in the wingspan of around 2 meters, to keep it in view. Need to be able to swap out lipos without removing the wing during the day. One or two piece plug in wings, would be nice. They could be be removed for my return to home, but not essential. I can fit a fully assembled Phoenix 2000 into my car. I have been flying an HK Phoenix 2000 for two or three years, and like the full house ailerons and flaps, but, again not essential. So you experienced guys, what suggestions for 2018< please?