Geoff Parkes

Simon, i have tried all sorts of edf units, if 50mm i go for the FMS 4 s units, but dont run them up holding them, any pressure on the fan case will force the blades to fly off, anything above this i go for Chain-sun units from RCCastle in China, superb service and if you pay for air mail-only a few dollars more they usually arrive in14 days, the fans are balanced so you get that turbine sound, there is a company in France Turbines rc i think , they are worth alook.

Richard, i dont know how you keep thinking of the funny posts you keep coming up with, any one that reads your war bird replicas sites know what i mean , how you design and produce your amazing kits and have time to think up these funnies is amazing. Back on topic, my local model shop has loads of balsa, all SLEC supplied, they are based in KIngswinford in the West Mids. their name is Penn models and they do mail order, give them a try, they have been going for over 30 years.,

Fond memories i had a 29 and a15, for the 15 i built a team racer , if i remember it was a russian model aeromodeler plan with swept back wings ?, in my inexperience i sanded the wing the wrong way round, so i used the wing swept forward with a MCKoy glow engine for rat racing, was fast and flew well until i got my feet tangled in someone else lines on the floor, it was terrible stunter and soon demolished itself on the ground, my memories of the 15, you warmed it up on a large prop and then used the smaller flight prop, again if i remember there was a guy Dick Edmonds? who used to "tune" ETA 15s i sent my motor off to him , when it was returned i could not wait to try this tuned motor, bad news it was slower than standard- happy days, racing motors, no silencers and no jobs worth trying to stop you enjoying yoursalf

Richard , could you save one of your motor mounts for me please, i have a Predator motor on order from Wheelspin at the moment. Could you also send me a set of retracts, let me know how much and I send a cheque to cover, oh by the way the prop blade packers arrived recently, as usual above and beyond service, regards Geoff.

Martin, if you are looking for a long term project ,i think you have found one, i have been on my Chippy for 2+ years and at last its complete and ready for paint, i have test run it down the back lawn and all seems O.K. its electric and i was interested to see if there was sufficient power to fly, it did not take off, but you can tell if there is enough power , similar set up to Dannies, but slightly smaller motor, but 6 s battery . My main grey area when building the wing was trying to understand the underside mid section of the wing, i used an underside photo in a Fly-Past mag, i think it was an article on the B.B.M.F. and there was a flying underside shot of their Chippy. best of luck with yours, if you are looking for balsa and in the west mids., try Penn models at Kingswinford- after the shut down obviously, i was in there just before shut down and they were well stocked for balsa and other hard woods and reasonably priced.

Richard, great news on you seeing the proverbial light at the end of the tunnel with getting the P51 kits sorted, i am in no panic for mine , i have a B.T. Hurricane and a Duncan Hutson Chippmunk to finish before starting the P51. If the kit arrives too soon it will be to much of a temptation to start it, this is what happened to the chippy ,i just looked at the Hurricane plan and before i realised i had the tailplane , elevators , rudder and fin built so, December or even Jan. is O.K with me , if that is O.k, with you, regards geoff.

Been in to my local model shop this morning to check on their balsa supplies , the shop is Penn models in Kingswinford West Mids. they are as well stocked as usual with plenty full quantities of all sizes of balsa and hard woods, prices seem to be reasonable and they do mail order, if you live in the area give them a try.

Steve , Ron, many thanks for your patience with me, i have a 5 year old Toshiba computer, its got so many ports on each side and accross the front , just used the ports to the right of the computer, but on the other side next to the power jack is another port which has a blue bar , i think one of the guys said was a power out port, i plugged into this and low and behold it WORKS, as i said before many many thanks for bearing with me on this problem, now onto sorting the rest of the tranny. have either of you managed to put speech onto your tranny, i have a 16 gig micro sd card and Richard at T9 has sent me speech files do i just down load the files onto the card and put into the tranny or do i connect the tranny to the computer to do this ?Regards Geoff.

steve , sorry to be a pain, i have connected the cable as your suggestion, but how do i check its charging, the manual tells me there is a green light to the bottom left looking at the rear of the tranny,it does mentionX9d +legacy models ,not certain if this is on the 2019 version, should i be looking any where else for evidence of charging ?

Earlybird , sorry for being dim, but my computer knowlege is limited, do i just connect the one end of the lead supplied with the tranny to the USB port in the battery bay of the tranny and the other end into my computer ? , will the computer just then charge the battery or do i have to do something to the computer to get it work ? i have been using a charger set to Li-ion but this does not balance charge, i am assuming that the on board charger in the tranny works this out as there are only 3 wires from the battery and no balancing wires, many thanks for your help, as i said previously after 30 odd years as a Futaba user, i am slowly coming to grips with open TX, its taken a month to programme my first model into the tranny, but it is slowly coming together, i doubt if i will ever get near to what this thing can fully do, but my aim is to slowly extend my knowlege , as you use the tranny you slowly discover what took a day to get to work previously becomes second nature , regards Geoff.

I have just purchased a taranis X9D plus 2019 transmitter, this is my first dip into open tx technology, as you may know you dont get a battery with this transmitter, so i also purchased a 2s1p 2040ma/h Li-ion battery(all from the very helpfull Richard at t9), you do not get a charger either with the transmitter, you charge through the USB port, the transmitter does have an onboard charging curcuit , but does anyone own one of these new transmitters and can advise me what charger they use? the users manual from T9 gives a spec,for the charger of less than 5 volts@ 2.1 amps via the USB socket, does anyone know of a suitable charger ?

Sorry guys for jumping into this topic, as soon as i posted my reply i realised that i should have initiated a new topic, will do now ,but thanks for the replies, as usual there is someone out there prepared to offer help, regards Geoff.

I have just purchased a Taranis X9D plus 2019 transmitter, this is my first dip into open tx technology, as you know you dont get a battery with this transmitter, so i also purchased a 2S1P 2040ma/h Li-ion battery ( all from the very helpful Richard from T9 ) you do not get a charger either with the transmitter, you charge through the USB port ,the transmitter does have an onboard charging circuit . But does anyone own one of these new transmitters and can advise me what charger they use ? the users manual from T9 gives a spec, of Less than 5 volts @ 2.1amps via a USB adapter for a suitable charger. Many thanks .

Again many thanks for all you replies, looks as like me going for the Radio masterTX16s, keeping the Futaba receivers for my other 7 chan. Futaba tranny.and buying compatable receivers for the 16s. regards all.

Thanks for all your input, i am swaying from the Radiolink AT10 and Kens. suggested radiomasterTX16s. I have been in touch with Hobbyrc and asked if i can use my Futaba Faast receivers with the radiomaster tranny , the bad news is they dont think i can, so my final question is - is there any one out there who uses the radiomaster TX16s with Futaba receivers , again many thanks for the replies, regards Geoff.