Ron Gray Posted March 10, 2021 Share Posted March 10, 2021 Firstly, I am using the term laminating film as a generic term, whereas it really should be called encapsulating film! It has been suggested that I start another thread specifically related to laminating film and in particular for those who want smaller quantities than that commonly sold. Having said that it could also be used as a thread for all things relating to laminating film as there is quite a bit of interest in this alternative covering material and there are a few of us who have had experience using it and can pass on tips to help those who have never used it before. One of the hurdles faced when thinking of using laminating film is the quantities that it is usually supplied in, commonly minimum roll lengths of 75m! So I have ordered 150m of it and am happy to cut this to length for fellow members. I've gone for the 38 micron thickness as that is, IMO, a good all round thickness that can be used on models 600mm WS upwards. When I bought my first lot (I shared the purchase with a fellow club member) it was in a roll approximately 300mm wide and whilst this is fine for smaller models when it came to the larger ones with a wider chord it meant a joint along the length of the wings. That hasn't been a huge issue as I managed to sand the edges down so they aren't that noticeable but I would rather not have the join at all, so the rolls I've ordered are 615mm wide. My original film was with a gloss finish which meant that I had to key the surface with fine sandpaper before I painted it. Again its not a big issue and there is an advantage in carrying out this exercise as it highlights (with ripples and bubbles) areas that haven't stuck down! Once again to help get over this the lam film's finish is ultra matt which should require very little prep before painting. So, in summary, I have 150m x 615mm wide rolls of 38 micron, ultra matt lam film on its way to me (I will post on here when I have received it). Other than the cost of packaging and postage I will not be adding anything to the cost, so it will work out at £0.58 / m. You can order as much or as little as you want and payment for it will be through PayPal (you pay their charges or pay as 'gift') or through bank transfer. Payment details will be dealt with through the PM part of this forum. Any questions please do ask. I'll trawl through the other threads and try and pick up all those who have already expressed an interest. 3 Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 10, 2021 Author Share Posted March 10, 2021 Names I've got so far: @Graham Davies 3 - 20m @Eric Robson - 20m @DaveB1 - 10m @Gary Clark 1 - 10m @Outrunner - 10m @Chris Bott - Moderator - 10m @PatMc - 10m @Bruce Collinson - 10m Quote Link to comment Share on other sites More sharing options...
Dwain Dibley. Posted March 10, 2021 Share Posted March 10, 2021 Put me on there for 20m Ron. I am intrigued to try the tissue over the top of this, as I love the look of a tissue finish. D.D. Quote Link to comment Share on other sites More sharing options...
leccyflyer Posted March 10, 2021 Share Posted March 10, 2021 Count me in please Ron - I'll take 20m thank you. ? Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 10, 2021 Author Share Posted March 10, 2021 Looks like I may have to order some more! Keep it coming guys! Quote Link to comment Share on other sites More sharing options...
MattyB Posted March 10, 2021 Share Posted March 10, 2021 No need for me to buy some as I was in on a previous group buy some years ago, but if you want to learn from the guys who first discovered this stuff take a look at these three threads on RCGroups... Quote Link to comment Share on other sites More sharing options...
GrumpyGnome Posted March 11, 2021 Share Posted March 11, 2021 HI MattyB That link takes me to some missing messages ? GG Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 (edited) Thanks for that @MattyB the more info we can have in one place the better for everyone interested in lam film. Regarding RC Groups, this is a good start Lam film as there are quite a few other links in the post, and then more links within those! Just be aware that if you're not used to RC Groups some of their threads can get a little heated! Edited March 11, 2021 by Ron Gray Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 I've pulled together the vids that I did regarding lam film 1 Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 2 more uses for lam film, covering plans to build over, separating fuselage sides when building one on top of the other (assuming, like me, you no longer have stock of covering film backing!). Quote Link to comment Share on other sites More sharing options...
stu knowles Posted March 11, 2021 Share Posted March 11, 2021 Put me down for 20m please. I have sent you a pm with contact details. regards and thanks, stu k Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 (edited) ? looks like I need to order some more! Edited March 11, 2021 by Ron Gray Quote Link to comment Share on other sites More sharing options...
MattyB Posted March 11, 2021 Share Posted March 11, 2021 6 hours ago, GrumpyGnome said: HI MattyB That link takes me to some missing messages ? GG Sorry - it was a link to some search results that worked when I tested initially, but doesn’t now. Here are the direct thread links... https://www.rcgroups.com/forums/showthread.php?790302-The-NEW-stuff! https://www.rcgroups.com/forums/showthread.php?825931-Unreal-Rehab-Potencial-with-The-NEW-Stuff-! https://www.rcgroups.com/forums/showthread.php?880408-The-New-Stuff-REVEALED Quote Link to comment Share on other sites More sharing options...
Sparks Posted March 11, 2021 Share Posted March 11, 2021 (edited) Hi Ron Could you put me down for 10m when you next order please. I'll PM you contact details. Sparks Edited March 11, 2021 by Sparks wrong name! Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 @Dwain Dibley. - 20m @leccyflyer - 20m @stu knowles - 20m @michael cawood - 10m @Sparks - 10m Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 Doubled the original order to keep up with demand! Quote Link to comment Share on other sites More sharing options...
Dave S. Posted March 11, 2021 Share Posted March 11, 2021 I'd like 10 metres please. Quote Link to comment Share on other sites More sharing options...
john stones 1 - Moderator Posted March 11, 2021 Share Posted March 11, 2021 Gonna need a bigger boat. 1 Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 @Dave S. - 10m Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 11, 2021 Author Share Posted March 11, 2021 Just had an email from the supplier to say it should be with me tomorrow. When it’s here I’ll have a better idea on packing, either flat in big envelopes or rolled in cardboard tubes. 1 Quote Link to comment Share on other sites More sharing options...
Gary Manuel Posted March 12, 2021 Share Posted March 12, 2021 (edited) Hi Ron. Would you mind sending me 10m as well please? PM sent. Edited March 12, 2021 by Gary Manuel Quote Link to comment Share on other sites More sharing options...
GrumpyGnome Posted March 12, 2021 Share Posted March 12, 2021 @MattyBCheers GG Quote Link to comment Share on other sites More sharing options...
Ron Gray Posted March 12, 2021 Author Share Posted March 12, 2021 @Gary Manuel - 10m Quote Link to comment Share on other sites More sharing options...
Basil Posted March 12, 2021 Share Posted March 12, 2021 Ron, could I have 20m please Bas Quote Link to comment Share on other sites More sharing options...
Eric Robson Posted March 12, 2021 Share Posted March 12, 2021 Ever thought of manufacturing it Ron, at this rate Oracover will call in the receivers. 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.