Here is a list of all the postings Ace has made in our forums. Click on a thread name to jump to the thread.
|Thread: Stripped thread bodge|
I have had good results with J B Weld (original cold weld). steel epoxy.
So long as the metal is absolutely clean it sticks like snot to a horsehair blanket - and is hard and good for 300c.
Seems that it may now prove difficult to obtain which is a shame
If you can find some grab it - it is good.
Edited By Ace on 13/07/2018 11:54:03
Edited By Ace on 13/07/2018 11:59:24
|Thread: New caption competition|
"look" If you land I have some new batteries for you.
|Thread: Tom Neil|
For those who didn't know of him. - BoB pilot
|Thread: New caption competition|
Fixed wing kite flouts new CAA laws.
Edited By Ace on 10/07/2018 15:27:11
|Thread: Take off into wind ?|
Our patch is a circle so no problem with wind direction you would think. Fine if someone with common sense sets up first at 90', everyone follows However if those lacking C S get set up first because its next to the path, getting them to shift another 60m round falls on the same ears as reminding them not to reach through the prop when connecting a battery while its sat on their lap
|Thread: 1/12 Messerschmitt Bf 109|
Looking good Timo
I use to make my 1/12th combat's from blue foam covered in brown paper, quick, cheap, disposable but no where near as pretty.
|Thread: HK postage charges|
Watch out if buying from the global warehouse as anything over £15 will attract import duty and hostage collection fee from the carrier.
just looked and the Kinetic is out of stock in GB & EU warehouses.
|Thread: Laser Single Cylinder Valve Timing.|
Like Martin I think its the RHS on a small capacity Laser. The LHS looks to be 180' out between exhaust/intake.
Where is Jon hiding when you need him
|Thread: Radio systems|
+1 for BEB's sound reasoned advice
I started with a Futaba FF9 on 35Mhz and had a few glitches so switched to JR using DSM2 the early Spektrum protocol, which proved to be glitch free. I then purchased one of the last DX9's with dual DMS2 & DSMX. I personally have had absolutely no radio issues at all and it does everything I need and more reliably. Excluding dumb fingers & dodgy switches but hey that effects every make
One other major potential issue not mentioned so far that effects all makes concerns extension leads not securely fastened together, working loose or leads not pushed into receivers or making poor intermittent contact over time. I always use 100mm fly leads to help prevent this potential intermittent issue with thread, tape or plastic locks. Would appear in the air as a radio issue. Not saying it was but I genuinely don't believe their are any inherently bad major systems out their today.
|Thread: See-through OS wankel rotary engine running slow-motion|
Knew the principle but to actually see it in action - fantastic, thanks for sharing.
|Thread: Wot 4 Squared|
Watching with interest as I have a Mk 3 to start shortly
|Thread: PU Glue removal|
Thanks David, I thought the dark grubbyness was due to it attracting muck, however looking around there is some evidence of iron darkening PU type glues - you live an learn.
Resorted to using one of the foam emery sponges which shifted some - but not all. Guess I will just have to let nature run its course for the remainder.
Thanks both, but the black grubby mark the diameter of a golfball is refusing to budge.
I guess the grease from the skin will eventually lift it but would dearly love a faster solution.
I love PU glue and am normally very careful not to get any on my hands.
You know whats coming next - yes my latex glove sprung a leak and now I have some on my palm
Tried thinners, nail varnish remover & Isopropanol with no result - So what will shift it please ????
|Thread: New TV Channel|
Are you accessing these through transmitted Freeview over the airwaves from a mast or via a Freeview internet link? Only my std airwaves Freeview doesn't show 94 no matter ow many times I re-tune it
Tried retuning here in Yorkshire and nothing on Freeview 94 here
|Thread: Peterf's 1/4 scale Falcon Models Tiger Moth|
Fascinating to follow to a superb end result and take my hat off of to you for taking the time to show and explain your techniques and problem solving Just need to see it flying.
|Thread: Forum members' new models: Let's see them.|
Fascinating to follow to a superb end result Just need to see it flying.
|Thread: The Ohmen|
If weight is needed and space allows what about paralleling up a pair of 2200 to give 4400 x 3s?
More useful weight with better duration.
|Thread: Laser Engines - Technical questions|
Apart from UK and some of the colonies, I suspect the rest of the world uses Gasoline and even us Brits recognize the phrase, where as the Yanks/others probably wouldn't automatically recognize Petrol. Heart says P but head leans towards G. You may also wish to distinguish between 2 stroke and 4 stroke engines with FS.
My tuppence - Laser G25 FS
Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!