By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for dirk tinck

Here is a list of all the postings dirk tinck has made in our forums. Click on a thread name to jump to the thread.

Thread: Sabre made in Belgium
21/06/2020 23:16:14

Please don't count them !20200621_230030.jpg

21/06/2020 20:23:06

Just a paint test regarding rivets...20200621_211453.jpg

Thread: Phil's F-86 Sabre build thread
21/06/2020 18:58:24

Beautiful and accurate building Phil ! I remember you pointing me in the direction of inserts to realise the gunports.

It turned out to be a winning solution !! Great job !

Thread: Tony's F-86 Sabre Build
21/06/2020 18:04:50

That's my rule nr 1 ,Anthony , don't start a model when you're still working on one ! And yes , i have a spare sabre on the shelf ....but i have also another 35 unstarted kits next to it embarrassed!!

Keep building ! cheers , Dirk

Thread: Sabre made in Belgium
21/06/2020 00:04:08

I also did the repair on the damaged aileron :added a small piece of hard balsa and glued it in place.After a little sanding it's ready for primer and paint

20200620_214042.jpg

21/06/2020 00:00:09

The time left this evening was spent painting the top side of the rudder and fin in gray , like the original

20200621_000447.jpg

20/06/2020 23:56:39

Thanks guy's for the offered help and info ,i'll be testing the masks next week.

I was planning to glue the canope frames in place (already painted )when i realized,if i want to replicate the rivets , now is the time so i did some testing on a test frame.

I try'd to make little pits with a sphere-like dremel bit but it's very dificult to make them all the same size .

Then i try'd to do the same with a small drill ,they're all the same size but in some cases i drilled right through !

This made me realize , maybe that's the best way :Drill them all through and fill them with epoxy !This is only possible with some tape on the back side. So drilled the holes , tape them on the back side , fill them up with epoxy and wiped off most of it left me with a workable solution.Tomorrow i will paint the test piece to see the result , looks good !

20200620_235934.jpg

20200621_000033.jpg

18/06/2020 21:37:32

Elevators and some little parts painted !That completes the Italian jacket!

On with the decals after some testing with paintmasks from Alan Gorham: Another challenge ..

20200618_221429.jpg

20200618_221448.jpg

X

Thread: Waterslide or vinyl decals?
17/06/2020 23:12:33

Hi Geoff ,the easyest way to paint them is by using paint masks (low tack vinyl)made thesame way as vinyl decals.

Thread: Sabre made in Belgium
17/06/2020 22:54:23

Thanks Dwain ,after polishing it will look much better !

Yes Phil ,just a personal touch , altough in some photo's it looks like they used it too ?

The damage on the aileron is in the white part , the most forgiving color,luckely...It happened by pulling the tape the wrong waysad. Another tip i guess ?

20200617_231143.jpg

17/06/2020 21:41:22

Trying to remove the masking paper, i managed to get one aileron damaged sad...My first repair and she didn't even left the shop !

Left side 2nd pic

17/06/2020 21:36:22

Another painting session resulted in blue wingtips! Not easy masking with the windsplitters on the topside. One side is white, the outside is blue:Where do you place the seam?

20200617_222223.jpg

20200617_222315.jpg

20200617_222355.jpg

Thread: Phil's F-86 Sabre build thread
16/06/2020 22:29:34

Hi Phil ,the only thing i can think of,as a cause of your filler problems is a reaction of a underlying product like glue ?

Maybe run a test piece ?

I can see now that your trailing edge fillet is vanished under the fin fillet ! I had thesame problem and i dropped a piece of the rudder onto the fin embarrassed...

Did you open up the channel for the elevator joiner ?Not enough travel ?My elevators are touching the fuse at their leading edge when i give full up(movement planwise )

Too late now to change.I hope i have enough ''up''with reduced elevator travel...

Thread: Chris McG F-86 Sabre Dog build blog
13/06/2020 19:56:25

Hi,Chris !

As you can see in my blog -begin ,i glue the sheets together before glueing them on the ribs. This way i can sand the skins in advance.

If you sand the skin after offering it to the wing ,then you sand more on top of the ribs and less between the ribs.(you push the sheeting down) Result :a golf terain !

There's only 2 glues in my shop :epoxy and zap ,red and green.

Cheers friend !

Thread: Sabre made in Belgium
13/06/2020 17:32:47

Hello all !

I'm trying to paint a part every day, even if it's a small one, keeping a steady pace.

Another important tip i had to find out the hard way:

If you mask a new painted surface be sure to put on a extra layer or two

of tape next to the area you're painting because the paint solvents still attack the underlaying fresh paint even if it's a week old or more!

20200613_181120.jpg

12/06/2020 22:13:47

Added the bleu tonight, just a few day's short to make it to the deadline!

20200612_224926.jpg

20200612_230358.jpg

10/06/2020 21:25:25

Just a little update today.

I painted the canope frames after a last fit on the fuse.

Not easy to clamp these fragile things!20200610_220017.jpg

10/06/2020 12:58:14

No room in there Andy !But the idea crossed my mind though!wink

Let' s hope it hits the magazine so it lives forever!

08/06/2020 23:11:58

After a long day's work , it's time for some aeromodeling therapy !Wife's orders !

With the wing ready to paint, for ages (!)i made a support so i can turn it over whilst painting it.

The weird masking on the ailerons is there to cover the bleu paint on the inside .I didn't mask the tips ,wich will be painted bleu,to keep the masking lines between colors to a minimum.

Degreased and blown clear of dust, Rattle the cans !! Even in this mild temp's i preheat the cans a little ,it makes the paint flow smoother and keeps the pressure up !

x20200608_215953.jpg

20200608_220013.jpg

20200608_231130.jpg

20200608_231155.jpg

20200608_231235.jpg

x

06/06/2020 18:18:49

Thanks Dwain ,skills you can learn , patience needs practice , setup is...well it's tape and a rattle can ! and you tube !!

Latest Forum Posts
Support Our Partners
Slec
electricwingman 2017
Sussex Model Centre
CML
Sarik
Advertise With Us
Latest "For Sale" Ads
Has home isolation prompted you to start trad' building?
Q: The effects of Coronavirus

 Yes - for the first time
 Yes - but Ive bashed balsa before
 No - Ive existing projects on the bench
 No - Im strictly an ARTF person

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E!