By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for J V R

Here is a list of all the postings J V R has made in our forums. Click on a thread name to jump to the thread.

Thread: sc 46
30/07/2013 14:32:51

Hello DG

I have an SC 32 & found that the low speed needle needed a lot of adjusting even though it was factory set I think I screwed it in around a complete turn to get a good tick over and pick up

Thread: Take off and Landing on a postage stamp!
03/06/2013 02:05:55

When I got back into model planes after a 25 year break, I taught my self to fly & would go round to my local park at around 0530hr there would be a couple of dog walkers about & I just waited for them to move on and clear my space. I did join a couple of clubs but I still pop around to the local park to fly.

30/05/2013 14:09:31

Hi Dickster

I'm familiar with ''that'' tree just to the right of the entrance gate on the other side of the road at the corcord club, and it's getting bigger..........

Thread: Calling All Tucano Builders!
19/05/2013 23:20:07

very slow progess on mine, I started this over a year ago & got side tracked with other things

imag0375.jpg

Thread: In your experience what's the most common cause of a crash?
09/05/2013 20:57:27

I selected other as most of mine have been down to orientation

Thread: Digital Copies
03/04/2013 11:01:59

Ive had problems in the past, but its working for me today

Thread: What are your 2013 build plans?
07/03/2013 22:58:40

The big ship is finished, its got a new SC32 which needed a lot of fiddling to get it to run right, the bottom end needle was much to rich & I have fitted a hot plug to make the bottom end run smoother as it only needs around 1/4 throttle to fly imag0326.jpg

Thread: Should we be licenced
10/02/2013 23:47:40

Pete B

Fingers crossed no revolution then............

10/02/2013 23:24:14

May be the damage has been done by posting this thread on an open forum ??

Thread: Building Boards - again
08/02/2013 11:21:17

IanR, I would mix up some 20 minute epoxy & pour into the dip on the work top then use your straight edge to pull the epoxy across to fill the hollow, remove the excess, job done.

Thread: What else do you do?
01/02/2013 17:00:06

Hi Dave,

is that the same Tillings that owned TB ( Bromley ) & TL ( Catford ) garages ??

28/01/2013 00:01:07

well I'm a semi retired bus driver, driven since 1978 & now work 2 days one week, then 3 days the next week so working only 6 months of the year, With all this bad weather I have been building,ready for the new season. When the weather improves I have also got ex military land rovers that I take to shows during the summer months.

Thread: Radian & a bit of wind
22/01/2013 16:13:06

sorry for butting in on this thread, I have the radian 3ch what is the correct C of G point ?

Thread: Flying Goals for 2013
22/01/2013 11:11:30

I must get out flying more than 4 times this year...........

Thread: Best ever purchase?
21/01/2013 23:06:56

an Eberspacher Hydronic heater to run the central heating in my workshop with an out put of 5kw & 3 rads = 19 degrees in my shed even if its -5 outside.

Thread: digital issues
10/01/2013 14:31:03

OK this is weird, last week I could view January 2009 issue, then it stopped working over the week end, but I could look at any other digital issue. I have just tried using Internet explorer & it works, back on Firefox its not working but I can still view other dates of the digital copies.

10/01/2013 13:40:14

Yes Phill lots of other copys work.

10/01/2013 13:27:56

Hi Phill

Just tried that, still no joy

10/01/2013 12:48:34

Looks like its a local problem then, I've had an e-mail reply from David Ashby & he said to contact the subscriptions dept which has been done and they said they would look into the problem, but no change yet.

10/01/2013 11:59:15

checking back on digital issues I can not view January 2009 or the 2008 special, I don't keep the old copies of RCM&E so use the digital issues as a reference. My subs are up to date till April & I can look at any other digital copy but not Jan 09 & 2008 special. This is the box that I get when I click on the digital copy

screen 1.jpg

Latest Forum Posts
Support Our Partners
electricwingman 2017
Sussex Model Centre
Slec
CML
Advertise With Us
Sarik
Latest "For Sale" Ads
Has home isolation prompted you to start trad' building?
Q: The effects of Coronavirus

 Yes - for the first time
 Yes - but Ive bashed balsa before
 No - Ive existing projects on the bench
 No - Im strictly an ARTF person

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E!