By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Graham R

Here is a list of all the postings Graham R has made in our forums. Click on a thread name to jump to the thread.

Thread: Warbird Replicas Bf 110 club.
15/05/2017 21:09:26

Hi Paul,

Nice neat solution for the flap. Have been busy today marking up the wing. Glued on l/e strips and started to make a hot wire cutter to cut out flaps etc.


I like your moth, guess it won't be long before it's maiden.

14/05/2017 21:25:44

Hi Paul

Thank you. I think that may be a job tomorrow. That will start the wing build.

14/05/2017 20:10:11

Making good progress Paul. Are the servo wells pre-cut and hidden under the obechi or do they need cutting out from scratch..

Ps hope its not man flu!

12/05/2017 19:53:14
Posted by Paul Johnson 4 on 06/05/2017 09:40:59:

Well..... they are on... glue drying.... very pleased.20170506_091553.jpg

Paul, where are the flap servos?

Are the servo wells precut into the foam and covered by the veneer, or do they need cutting out?

Edited By Graham Russell on 12/05/2017 19:54:10

11/05/2017 21:11:20

Thanks Dwain.

11/05/2017 18:07:16

Paul the area I mean is the area on the bottom of the fus immediately behind the tail wheel also the back end between the sides an behind former F8.

Thread: Who Else Wants a 63" Lavochkin La7 kit?
11/05/2017 18:00:30
Posted by RICHARD WILLS on 11/05/2017 17:27:32:

Graham ,

I think you would be better off with the smaller La7 as it works so well in electric form . Might have to deal with that separately at a later date.

Anyone out there that wants a big La7 better put their hand up . The last batch was in 2011 !

Not likely to get a second go on that basis . Dont want any "grizzlers"crying on the phone after the boat (aircraft carrier) has sailed.

Hi Richard, I do have a spare Hacker A60(2600w) is a Hyperion zs4035 (1500w) or failing that an old laser75 cir 1990

11/05/2017 17:22:02

I also would be up for one if it's a bit later in the year. My modelling budget has been hit a bit with the purchase of a WB Spitfire and Fg110.

Would it take electric or do I need to re-invest in ic (Having gone totally electric)

Thread: Warbird Replicas Bf 110 club.
11/05/2017 17:14:39

Nobody has shown their rear end yet! Is it just filled in and rounded off behind the tail wheel?

2. What did you do with the edge along the cockpit? It needs rounding off. Did you add an extra doubler on the inside edge so that the outside edge can follow the outside contour? Once I've sorted these 2 problems my fus will have finished the building stage.

11/05/2017 13:03:54

Hi Nigel. Welcome back and trust you will get sorted soon.. I'll be very interested to see how you do your hinges for this project and for gliders.

05/05/2017 20:27:42

I'm a happy chappie, got my back end sorted. All surfaces working, at last.

Dwain, like you I ended up cutting out a lot of t/p sheeting to get the rudders sorted. Have now got control rods in. I can now get on with the rest of the fus installing decking etc. Nice tidy garage you have there.

Edited By Graham Russell on 05/05/2017 20:29:24

02/05/2017 21:36:46

Back on the thread. Have been a bit busy getting a few gliders ready for our liver day last Saturday.. I have now got a reasonable movement on the rudders. One problem I have is finding a way on the set it up so that I can centre up the rudders. (Give us a clue Richard).

Thread: Who wants a Warbird Replics Hurricane?
02/05/2017 21:16:36

opps wrong thread




Edited By Graham Russell on 02/05/2017 21:35:23

Thread: Warbird Replicas Bf 110 club.
28/04/2017 11:51:41

How much rudder throw do you need? I'm having trouble getting much movement on left fin, left rudder and right fin right rudder.

26/04/2017 12:07:09

Paul, yes like yours. I have some K &S brass strip which I silver soldered after I cleaned up the joiner. I use a small blowtorch. The joint does feel pretty secure.

26/04/2017 11:25:17


As Richard said, it's the viscosity of single cream. I found that if when you are painting it on it and it gets hard to brush out it's a little thick. The brown paper is quite absorbing. When you going over an edge e.g around the fin, I found it useful to paint some water on the opposite surface. It seemed to help. The method of application was as Richard suggested.

I have thought about some building photos, but you and Paul have covered most aspects. The only modification I have made was to silver solder an arm on the elevator so that the servo linkage is all inside the fus.

I still have the wings to cut and fus to complete.

Hope all this helps


26/04/2017 08:04:20

Spoke with Richard yesterday about covering with brown paper. After that I covered the t/p and fins, It was so easy, very pleased with the result. To other warbird builders who may be unsure- give it a try.(and it's real cheap).

Thread: Warbird Replicas Spitfire LF mk IXc
24/04/2017 22:59:07

You ought to try Stinking Bishop - It is what is says.

Thread: Warbird Replicas Bf 110 club.
20/04/2017 16:46:51

All I can say is Watch out poor people of Padstow. If you want some peace Richard there is a bike hire place just down in the carpark next to Steinland. Hire them a bike and send them down the Camel trail, tell them not to come back until they spot a camel. All that sea air should clear the dope out of their little heads.

18/04/2017 10:31:04

So what are we saying. I'm sure that for us who are venturing into our 1st twin especially electric would like to know and how to prevent it.

I thought that we were almost guaranteed to be problem free. Was it a possible battery power problem? To me it looked like a classic stall . Is it a case for telemetry monitoring of both batteries outputs?


Edited By Graham Russell on 18/04/2017 10:33:07

Latest Forum Posts
Support Our Partners
Sussex Model Centre
electricwingman 2017
Advertise With Us
Latest "For Sale" Ads
Has home isolation prompted you to start trad' building?
Q: The effects of Coronavirus

 Yes - for the first time
 Yes - but Ive bashed balsa before
 No - Ive existing projects on the bench
 No - Im strictly an ARTF person

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E!