By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by CML

Companion2.2 - Taranis X9D anomalies

All Topics | Latest Posts

Search for:  in Thread Title in  
PatMc02/05/2018 16:15:33
4200 forum posts
521 photos

I upgraded my Taranis to 2.2.1 at the weekend, when I came to make some model configuration changes via Companion I came across some issues. It seems that access to the two slider controls are missing in the edit facility. They're also missing from the simulator & the switches are shown out of order to their position on the actual Tx.
I vaguely remember reading somwhere a while back about th e odd switch order but can't recall anything regarding the sliders.
Does anyone have any info on this issue or perhaps know if it's likely to be addressed in the next version of 2.2 ?

Mike Blandford02/05/2018 17:09:12
530 forum posts
22 photos

Check in the radio settings that LS and LR are set to "Slider with Detent" as opposed to "None".


Bob Cotsford02/05/2018 17:11:28
7973 forum posts
439 photos

Never noticed that Pat, well spotted. Open a backup or load your models from the transmitter, then click on 'Edit Radio Settings' and select the 'Hardware' tab. Set LS and RS as 'Slider with Detent', save the profile and Bob's your Uncle, you should get your sliders back. I've just done this and those mixes using LS are still there, I didn't think to look before checking and amending the hardware config.


Edit: I just found an older backup and as you say, the sliders are not in the selection lists or simulator even though the mix lines still show LS.  Odd!

Edited By Bob Cotsford on 02/05/2018 17:15:06

Andy4802/05/2018 17:15:52
1378 forum posts
1 photos

The missing slider issue is a known issue and is still an open issue to be resolved for version 2.2.2 when it comes out. Mike's answer will solve the problem for you, however.

On the simulator, the switches are now placed alphabetically. This is because OpenTX now supports so many different transmitters and some have their switches in different physical places.

Bob Cotsford02/05/2018 17:27:42
7973 forum posts
439 photos

Andy, unless you manually configure LS and RS they don't exist in the model options. Once configured they appear between the sticks in the simulator.

trebor02/05/2018 18:13:10
1906 forum posts
214 photos

That's handy I thought about an update but I will wait for version 2.2.2, saves me getting confused yes

PatMc02/05/2018 20:08:20
4200 forum posts
521 photos

Well that was painless.
Sorted in minutes by following Bob's method. thumbs up

Thanks, Mike, Bob & Andy.

Ironicaly, I only came across the problem because I was looking to make the left slider redundant in some E gliders.
I was experimenting to see how practical it would be to use the throttle stick to control spoilerons when the motor was off.
I've just set it up on my old faithful EasyGlider, hopefully will be able to try it out in the air in the next few days. If all goes well I copy the mixes over to the operate the crow brakes on my Vitesse then standardise across my other E gliders & pure gliders.

Edited By PatMc on 02/05/2018 20:09:56

Andy4803/05/2018 09:42:14
1378 forum posts
1 photos
Posted by Bob Cotsford on 02/05/2018 17:27:42:

Andy, unless you manually configure LS and RS they don't exist in the model options. Once configured they appear between the sticks in the simulator.

I Know. Mike already stated that above.

All Topics | Latest Posts

Please login to post a reply.

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E! 

Latest Forum Posts
Support Our Partners
electricwingman 2017
Gliders Distribution
Cambridge Gliding Club
Wings & Wheels 2019
Pepe Aircraft
Advertise With Us
Latest "For Sale" Ads
New Poll - Sticky situations...
Q: How often - when using superglue - do you end up with it on your fingers?

 Every time
 Wear rubber gloves

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us