By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by CML

What's your favourite way of attaching a canopy?

All Topics | Latest Posts

Search for:  in Thread Title in  
Adrian Smith 120/09/2019 15:14:42
avatar
2249 forum posts
975 photos

For the first time in a while I have project that requires attaching a large canopy to the fuselage. In the past I have had limited success using Pacer Formula 560 canopy glue and wondered if anybody has any better/more successful ideas?

Thanks

Martian20/09/2019 15:36:38
2217 forum posts
1091 photos

I have used canopy glue  sparingly but had to hold in place with tape etc my favoured way is with 1mm screws

Edited By Martian on 20/09/2019 15:38:21

Denis Watkins20/09/2019 15:43:43
3875 forum posts
58 photos

20190727_112230-1.jpgLike Martian, I use micro screws, into 1/32 ply,

Pre drilled, and hidden under the window frames, bonded into the balsa

20190727_112220-1.jpg

Adrian Smith 120/09/2019 15:51:28
avatar
2249 forum posts
975 photos

Thanks Denis, Martian makes a lot of sense.yes

Don Fry20/09/2019 15:59:17
avatar
3911 forum posts
42 photos

A variation on Denis, I drill everything into the balsa, attach it, and when Happy, remove the lot. Wick thin cyano into the holes to harden them, and reassemble at leasure.

Bob Cotsford20/09/2019 17:09:39
avatar
7963 forum posts
439 photos

Canopy glue, then a 1/2" wide strip of trim film carefully ironed over the join with a coolish iron or for a painted model an additional fillet of canopy glue around the edge. If the canopy has a flange that sits flat to the fuselage then I have on occasion used screws in the same way as Don.

I do like Denis's idea for canopies that don't sit flush though, I may have to pinch that one. I could have used it on my Lavochkin but that is securely attached with canopy glue now.

Paul Marsh20/09/2019 17:30:56
avatar
3703 forum posts
1050 photos

Canopy glue then screws.

dscf0150.jpg

Tom Sharp 220/09/2019 18:38:24
avatar
3514 forum posts
18 photos

Six inch nails.

Robin Etherton20/09/2019 20:17:42
271 forum posts
41 photos

Now you’re getting ridiculous.

At least 7 inch are required

Ronaldo21/09/2019 00:49:44
avatar
231 forum posts
17 photos

Nah, ... 12mm cavity wall bolts, can't pull out then thumbs upwink

robert chamberlain21/09/2019 07:23:01
122 forum posts

guys--, I have had limited success with the 560 stuff. Just for looks I cut down brass brads and added a few . If you drill a hole the same size as the brads it usually splits the canopy. Years ago I bought an attachment for my Dremel which cleanly sliced a grove down each side so the canopy fits flush but sadly have not seen the ad for years now. BTW, several years ago I posted an idea about dying the canopy. I used RIT cloth dye . Warm water in a tub and soak it for awhile. Oddly it has only worked on one kind of plastic and not on others. CA glue out gasses and messes up the plastic.------------------------Bob

Rich too21/09/2019 07:32:05
avatar
3002 forum posts
1061 photos

+1 small screws yes

i could never get on with canopy glue and screws look so much better anyway...

Adrian Smith 121/09/2019 08:54:51
avatar
2249 forum posts
975 photos

I have had the canopy spitting issue with small screws, Robert. However, that was in my I/C days and I have noticed with electric models there is much less vibration and probably should be less of a problem.

Rich, I think I will try small screws with some very small grommets I have to lessen the "splitting" factor. May be canopy glue plus screws although that sounds like overkill!

Chili Pants21/09/2019 09:21:54
23 forum posts
19 photos

I have used this to great effect, apply glue and hold canopy in place with tape until set, it is used by jewelers to affix jewels in watches etc, drys crystal clear as well and any excess is easily cleaned away, although with the applicator its hard to make a mess.

Got mine £2.99 on the bay, you cant go wrong with this stuff.s-l1600 (3).jpg

Josip Vrandecic -Mes21/09/2019 09:25:20
avatar
2993 forum posts
260 photos
When it comes to balsa/wood models, it's easy to mount any canopys, but that doesn't apply to foam construction .... every glue is a problem ... and then I use the least evil ... UHU por.blush
Ronaldo21/09/2019 09:33:30
avatar
231 forum posts
17 photos

I'm not a big fan of canopy glue, but it has worked for me. First I lightly key the gluing area with fine sandpaper, both painted and film covered surfaces, then apply the canopy glue, hold down the canopy with masking tape, then here's the important bit ... leave the glued canopy undisturbed for 48 hours. Takes a while to fully set I know, but works for me.

ken anderson.21/09/2019 11:02:10
avatar
8434 forum posts
772 photos

hello Adrian, consider using aquarium silicone,sml tube from local tropical fishshop aprox £5....small bead around the base of the canopy, keep in place with masking tape,leave overnight and trim any surplus off nxt morning...it'll stay on for ever... I've used the same method for years.

ken anderson....ne...1...aquarium dept.

Adrian Smith 121/09/2019 13:00:07
avatar
2249 forum posts
975 photos

That's an interest suggestion, Ken. Thanks.

I think in the past Ronaldo, I have been too impatient or the workshop too cold.

Another good one Chilipants!

Edited By Adrian Smith 1 on 21/09/2019 13:01:10

ASH.21/09/2019 18:48:32
avatar
304 forum posts

Hello Adrian, a quality clear silicon as Ken suggests, secured when dry with a few screws - works very well.

PS. Adrian, I sent the twin SH Glow unit to the chap in Australia, He is well chuffed. yes

Mark Stevens 104/10/2019 05:10:13
avatar
120 forum posts
48 photos

Don't think I've seen this mentioned yet but, has anyone ever tried hot glue for attaching canopies ?

It seems to stick to pretty much everything else in RC Models, especially being used on some stronger jobs and it certainly won't fog up clear screens. The big plus is that it sets fairly quick and can always be peeled off and re-applied later if need be.

I have a small hobby / craft size hot glue gun which will give a nice fine application of glue and have been considering using it to mount windscreens on a model. I just haven't got to that stage yet.

Mark

 

 

Edited By Mark Stevens 1 on 04/10/2019 05:12:08

All Topics | Latest Posts

Please login to post a reply.

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E! 

Latest Forum Posts
Support Our Partners
electricwingman 2017
Cambridge Gliding Club
Wings & Wheels 2019
Gliders Distribution
Slec
CML
Pepe Aircraft
Advertise With Us
Sarik
Latest "For Sale" Ads
New Poll - Sticky situations...
Q: How often - when using superglue - do you end up with it on your fingers?

 Every time
 Occasionally
 Sometimes
 Rarely
 Never
 Wear rubber gloves

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us