By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by CML

Hitech Optic 6 Tx

All Topics | Latest Posts

Search for:  in Thread Title in  
Adolfo Tristany 214/12/2008 21:35:00
1 forum posts
I own a HITECH OPTIC 6  Channel 35 Mhz Transmitter. Changing the battery I made mistake and now the Transmitter does not work well.  It emits but it gives not the signal to command the servos. Connected to a plane simulator  works very well.I ask if you know if this transmitter has a fuse or what component is necessary to change to fix it.Thanks very much for your attention.

Yours sincerely   

Adolfo Tristany
Former Member16/12/2008 11:52:00
6538 forum posts

[This posting has been removed]

robert chamberlain13/10/2020 08:49:05
175 forum posts

Hello, Will my Hitec 6 Optic run other brands of receivers or do I have to stay with Hitec all around?---Bob C

Frank Skilbeck13/10/2020 09:15:23
avatar
4935 forum posts
114 photos
Posted by robert chamberlain on 13/10/2020 08:49:05:

Hello, Will my Hitec 6 Optic run other brands of receivers or do I have to stay with Hitec all around?---Bob C

If it's 35 mhz then it will operate any 35 mhz PPM receivers, if it's 2.4 GHz then Hitec or compatibles which specifically state Hitec.

robert chamberlain25/11/2020 04:40:55
175 forum posts

I bought a Hitec Optic 6 trans and am having a problem with the on/off switch. Turns on OK , but just the slightest pressure on the switch shuts it off. Also the switch seems rather loose and really a bit cheap looking. Rather loose up and down as I move it. Anyone have a similar issue? Bob

Jonathan W25/11/2020 10:17:10
137 forum posts
11 photos

Mine went like that too, although it never caused a problem while flying. If any further deterioration can be expected, I don't know as I upgraded the radio and my old Optic is now only a spare.

Keith Berriman25/11/2020 10:23:41
851 forum posts
7 photos

Maybe worth a call to Mike Ridley workshop to see if he can change the switch for a new one .

Just thrown away all the interior from my old Optic

Phil Green25/11/2020 10:45:15
avatar
1682 forum posts
349 photos

My Optic 6 also has an intermittent on/off switch, exactly as Robert described. Seems like a common fault!

Easy fix though.

robert chamberlain26/11/2020 03:33:12
175 forum posts

I would like to get in contact with Mike Ridley about the switch on my Hitec. Anyone have an address, E-mail or phone number? Thanks.

 

Edited By David Ashby - Moderator on 26/11/2020 10:02:07

Roger Adams26/11/2020 08:58:05
95 forum posts

Google Mike Ridley radio workshop, details should be top of the list.

Keith Berriman26/11/2020 09:25:57
851 forum posts
7 photos

Robert 

Always ask people to pm you with any information

Edited By Keith Berriman on 26/11/2020 09:26:37

ken anderson.26/11/2020 10:06:49
avatar
8864 forum posts
820 photos

hello Robert...here's Mikes website details...not been funny,but it may cost more for postage/repair....why not get a replacement..

 

ken anderson...ne...1 ...radio dept.

Edited By ken anderson. on 26/11/2020 10:07:11

Phil Green26/11/2020 12:43:14
avatar
1682 forum posts
349 photos

Erm.... its a switch!

Easy DIY repair, its not rocket science... wink

robert chamberlain26/11/2020 19:15:22
175 forum posts

Well, all is well with my Optic 6 switch. Remember I said that the switch felt cheep and flimsy. The issue was that the gray switch really just went down into the radio and flipped the real switch. I carefully pulled it off and underneath was this real switch. I doubt there was a MM of slop between the real switch and the external slider. I am not even going to bother to glue them together. All is well now. It is even safer as the real switch is in further into the case and harder to accidently turn off. Your mileage may vary. Bob

robert chamberlain05/12/2020 13:49:59
175 forum posts

My Optic 6 Sport transmitter has , in my opinion, a hard to understand manual, or is wrong in some cases. It is version 1.0. I wonder if there is a later version written with more clarity ? Maybe a 2.0 or possibly someone out there has taken to re writing it as a project? ---Of course, there is the possibility that it is just mal functioning and never did work right out of the box.--Anyone out there have the same issues?

Keith Berriman05/12/2020 14:04:42
851 forum posts
7 photos

If I remember correctly it was two buttons to press to get to main menu and one button to press to set the parameters in the selected channel

All Topics | Latest Posts

Please login to post a reply.

Support Our Partners
Slec
Sussex Model Centre
electricwingman 2017
CML
Subscribe now
Advertise With Us
Sarik
Latest "For Sale" Ads
NEW POLL - has the pandemic altered your event safety perceptions?
Q: Has the covid pandemic deterred you from attending shows and events in 2021?

 No, I'll be attending just as many as I usually do
 No, but I'll choose my event with greater care
 Yes, I'll attend fewer events going forward
 Yes, I wont attend any where previously I have

Latest Reviews
Digital Back Issues

RCM&E Digital Back Issues

Contact us

Contact us

Magazine Locator

Want the latest issue of RCM&E? Use our magazine locator link to find your nearest stockist!

Find RCM&E!